ACCESSORIES
SIGNAL CONVERTERS
A transducer that selects the highest and lowest signals from up to six connected inputs and has two separate max. and min. converts it to an output signal. If you use less than six inputs, unused inputs will remain open. Both outputs can be used at the same time. No settings are required.


MM6-24 / D
Transducer
WITH TIMER SWITCH RELAY
Timer for installation in the room, can be activated at the touch of a button. The connection time can be 15 minutes, 30 minutes, 1 hour, 2 hours, 4 hours and 8 hours. The timer is turned off when the set time has elapsed or when the timer is pressed during the connection time.


TIM480N
Timer with changeover relay
INDUSTRIAL STANDARD COVERING
Plastic industry standard cover with transparent cover for DIN rail mounting.
IP65 protection class.






THERMOMETER
Thermometer for duct mounting. It is possible to fit different duct sizes with a movable mounting flange. The rubber seal prevents air leakage.



COOLING SPRAY
To regulate frost protection. It cools to -50 ° C.

CS-260
Cooling spray, 200 ml
TRANSFORMERS
ROTATION MONITOR
SPINN / D is an electronic rotation monitor that is primarily used to monitor rotating heat exchanger wheels. There is a changeover alarm relay and a function to block the alarm output in case of intentional shutdown.


SPINN / D
Rotation monitor

RR-G3
Sensor with magnet

MAGNET-424
Extra magnet
TEMPORARY PROTECTION FOR RS485 (EXOline) AND hIEXOline

X1804
Number of modules: 2.7
TRANSITION PROTECTION FOR TELEPHONE LINES

X4106
Number of modules: 1
RELAY MODULES
Connection module for electrical isolation between controller and load. It has screw terminals for easy and fast wiring. The module has a manual control function, an LED indication and a built-in protection circuit.

KR24-1W-S
Relay module, 1 relay, on / off / auto switch
Relay modules with potential-free, high-load changeover contact. The modules are insulated to DIN VDE 0106-101 and DIN VDE 0160.
The KRDC24-2WAU and KRAC24-2WAU are particularly suitable for use with microsensors.





PUSH-BUTTON
Push button for longer runs. Closing or disconnecting The PB can be selected with or without spring return.


PB
Pushbutton for flush mounting
WITH PUSH BUTTON INDICATOR
Push button for longer runs. Pressing PBI creates a momentary closed contact that activates the connected system for a longer run. The button has an incandescent lamp that can be connected to the system to indicate running as desired.
Support for 230 V AC and 24 V AC bulbs.


PBI
Pushbutton for recessed installation with indicator
MANOMETERS
DIFFERENTIAL PRESSURE MANOMETERS
Simple, compact, easy-to-use filter manometer. The MINI1200 is equipped with a measuring fluid, pressure outlets and a self-adhesive label for reading the filter type and for the initial and final pressure drops.


MINI1200
Manometer

MINI1200: 25
Manometer, 25 units
A tool for high-precision measurements. The manometer can measure a pressure difference of up to 600 Pa with an increased resolution between 0 ... 200 Pa. With blow-out protection and zero adjustment knob. Max. Total pressure 100 kPa.
The MV600 is equipped with measuring fluid, pressure nozzles, pipes, screws and a self-adhesive label to record the first and final pressure drop.


MV600
Manometer
PRESSURE GAUGE ACCESSORIES
MM-F2
Blue measuring liquid (MINI1200), 1.05 g / cm 3, 500 ml
MM-F3
Red measuring liquid (MV600), 0.786 g / cm 3, 30 ml

MTU: 25
Pressure nozzle, black plastic, for 6 mm pipe, 25 pcs
MTU: 100
Pressure nozzle, black plastic, for 6 mm pipe, 100 pcs
MM-P: 25
Plastic pipe Ø6 mm. Transparent, 25 m.
MM-P: 100
Plastic pipe Ø6 mm. Transparent, 100 m.
IPP8: 1000
Expansion plug, gray plastic, 8 mm, 1000 pcs
IPP10: 1000
Expansion plug, gray plastic, 10 mm, 1000 pcs
IPP12: 250
Expansion plug, black plastic, 12 mm, 250 pcs
T-ROR: 100
Plastic T-connector for 6 mm pipe, 100 pcs